GL7-CHA Charge/Accerometer Module
This is the input module for sensors based on piezoelectric elements capable of measuring a variety of phenomena including acceleration, pressure, and force. You are able to connect the BNC output from the sensor directly into our charge/accelerometer module which supports TEDS based sensors. Additional filtering capability allows accurate measurement of vibration and dynamic signal recording from piezo-based sensors.
High-precision measurement using various filters
High accuracy can be achieved using various filters using high-pass, low-pass, and anti-aliasing filters.
Supports a variety of piezoelectric type sensors
This module supports various types of piezoelectric sensors including accelerometers, forge gauges, and pressure transducer – all supported with direct sensor input using BNC or micro-connector inputs.
Type of sensor
Unit of sensitivity (example)
Piezoelectric type sensors
Charge output type
Voltage output (IEPE) type
Sensors with charge or voltage output using IEPE connectors can be recorded using the piezoelectric element. GL7-CHA module also sets the sensitivity and the unit of measurement scaled to its original units.
|Type of module||Charge amplifier module - for sensor based on Piezoelectric element -|
|Number of input channels||4 channels|
|Input method||All channels isolated unbalanced input, Simultaneous sampling,
BNC and Miniature connector (#10-32UNF)
|Sampling speed (interval)||100 k Samples/s to 1 sample/h (10 μs to 1 hr.)|
|Built in RAM||2 million samples for each channel|
|Input type||Sensor in charge output type, Sensor in IEPE type, Voltage|
|Input coupling||Sensor: Charge-RMS, IEPE-RMS
Voltage: DC, AC, DC-RMS, AC-RMS
|Measurement range||Acceleration sensor input||1, 2, 5, 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000, 20000, 50000 m/s2|
|Voltage input||DC, AC coupling: 50, 100, 200, 500 mV, 1, 2, 5, 10 V
RMS measurement: 20, 50, 100, 200, 500 mVrms, 1, 2, 5 Vrms
(Crest Factor in RMS measurement: up to 4 in 20 mVrms to 2 Vrms range, up to 2 in 5 Vrms range)
|Supported sensor sensitivity||Charge output type||0.01 pC/(m/s2) to 999.9 pC/(m/s2)|
|IEPE type||0.01 mV/(m/s2) to 999.9 mV/(m/s2)|
|Measurement accuracy (*1)||Charge output type||±0.9% of Full Scale ([sensor sensitivity] × [setting range] ≥ 20 pC)|
|IEPE type||±0.25% of Full Scale ([sensor sensitivity] × [setting range] ≥ 200 mV)|
|A/D converter||Successive Approximation type, 16bits (effective resolution: 1/40000 of the measuring full range)|
|Input impedance||100 kΩ ±5%|
|Excitation power||4 or 8 mA (supported voltage: 22 V ±10%)|
|Maximum input charge signal||Max. 50000 pC|
|Maximum input voltage||Between (+) / (-) terminal||25 Vp-p|
|Between channels ((-) terminals)||25 Vp-p|
|Between channel / GND||25 Vp-p|
|Max. voltage (withstand)||Between channels||300 Vp-p (1 minute)|
|Between channel / GND||300 Vp-p (1 minute)|
|Isolation||Between input / GND||Min. 50 MΩ (at 500 V DC)|
|Common-mode rejection ratio||Min. 80 dB (50/60 Hz, Signal source impedance: Max. 300 Ω)|
|Frequency response||Charge type||1.5 Hz to 45 kHz|
|IEPE type||1 Hz to 45 kHz|
|Filter||Hi pass||Off, 0.15, 1, 10 Hz|
|Low pass||Off, Line(1.5 Hz), 3, 6, 10, 30, 50, 60, 100, 300, 500 Hz, 1k, 3k, 5k, 10k Hz (in -30dB/oct)|
|Support TEDS||Standard||IEEE 1451.4 Class1 (Temperate No.25)|
|Support||Reading information from the sensor and setting it to module|
|Calculation function||Integration (convert measurement to velocity),
Double Integration (convert measurement to displacement)
|External dimensions (W x D x H)||Approx. 49 x 136 x 160mm (Excluding projections)|
|Weight||Approx. 850 g|
Subject to the conditions:
- Room temperature is 23ºC ±5ºC.
- When 30 minutes or more have elapsed after power has been turned on.
- Filter is set to 10 or Line.
- Sampling rate is set to 1 second.
- GND terminal is connected to ground.